SIIG UltraATA 100 Pro Instalační příručka stáhnout pdf

UltraATA 100 PCI

Quick Installation Guide

04-0196C

Introducing the UltraATA 100 PCI

The UltraATA 100 PCI is an ultra high-speed dual

channel UltraATA 100 controller board for use in

Pentium-class computer. With full support specified in

ATA/ATAPI-5, it achieves burst data transfer rates up

to 100MB/sec and supports drive capacities up to

128GB. And it also provides full backward support for

UltraATA 33/66, EIDE/Fast ATA-2, IDE and ATAPI

devices. PCI Plug-n-Play makes the installation quick

and easy, the enhanced BIOS auto-detects device types

and fine tunes to the best performance for each connected

IDE/ATAPI device.

Features and Benefits

• PCI Plug-n-play 2.1 compliant

• 2 independent IDE/ATA Channels, supports up

to four IDE/ATA devices and 128 Bytes buffer

• Supports ultra and multiword DMA timing modes

• CRC (Cyclical Redundancy Check)

• Built in 80-Pin cable detect circuitry

• Supports External BIOS

• 32-bit 33 MHz PCI Interface

• Supports bus master DMA at 133 MB/sec PCI

burst rate

• Supports maximum IDE/ATA data transfer rate of

100 MB/sec

• 3.3V Operating Voltage with 5V tolerant I/O

1 2 3 4 5 6 ... 13 14

Shrnutí obsahu

Strany 1 - Quick Installation Guide

1UltraATA 100 PCIQuick Installation Guide04-0196CIntroducing the UltraATA 100 PCIThe UltraATA 100 PCI is an ultra high-speed dualchannel UltraATA 100

Strany 2 - Package Contents

10To Verify Windows NT 4.0 Installation1. Click Start, Settings, Control Panel. Doubleclick SCSI Adapters.2. Highlight CMD PCI 646U2/648/649 Ultra DM

Strany 3 - Hardware Installation

116. Select Search for a suitable driver for my device(recommended), and click Next.7. Insert the Software Installation diskette into thefloppy drive,

Strany 4

126. Click Finish and restart Windows to completedriver installation.Windows XP/Server 2003 InstallationWindows XP and Server 2003 has built-in drive

Strany 5 - Driver Installation

Technical Support and WarrantyQUESTIONS? SIIG’s Online Support has answers!Simply visit our website at www.siig.com and click on Support.Our online s

Strany 6 - Windows 98/98SE

About SIIG, Inc.Founded in 1985, SIIG, Inc. is a leading computer upgrademanufacturer of I/O connectivity products, including PCI & ISAserial and

Strany 7 - Windows ME

2System Requirements• Pentium-class computer with one available PCIslot• Windows 95B/98/98SE/NT 4.0/2000/XP/Server 2003Package Contents• UltraATA 100

Strany 8 - Windows NT4.0

3Hardware InstallationGeneral instructions for installing the card are providedbelow. Since the design of computer cases andmotherboards vary, refer

Strany 9

41. Install hard disk drive(s) in chassis.2. Attach one connector on the long end of the UltraATA ribbon cable to the board's IDE connector andth

Strany 10 - Windows 2000

5Driver InstallationThis section provides information on how to install theUltraATA 100 PCI drivers for the following operatingsystems:Windows 95B ...

Strany 11

67. From the Insert Disk window, select OK, thenretype the path A:\Win9x and click OK.8. Remove the Software Installation diskette andselect Yes to re

Strany 12 - Bios Configuration

76. Select Search for the best driver for your deviceoption and click Next.7. Check Specify a location and type in a:\Win9xand click Next. Click Next

Strany 13

86. Click Finish, remove the driver diskette and restartWindows to complete the driver installation.For Existing Windows ME Installation1. Install the

Strany 14 - About SIIG, Inc

93. Screen 2, Windows NT Setup, Setup is loadingfiles, keep pressing F6 key to add the UltraATA100 NT4.0 driver.4. If screen 3 does not appear for opt