SIIG RS-232 to Multi-Mode Fiber Optic Instalační příručka stáhnout pdf

FiberOptic Card

Quick Installation Guide

This quick installation guide provides instructions for installing a 100Base-FX

PCI FiberOptic Card.

1-1 Introducing the FiberOptic Cards

SIIG's line of fiber optic Fast Ethernet 100Base-FX PCI cards fully

comply with all IEEE 802.3u standards. Four LED indicators are

provided on the bracket to help oversee the network/board link,

activities, collision and full-duplex status. The following models are

available :

• FiberOptic Card-ST (multi-mode)

• FiberOptic Card-SC (multi-mode)

• FiberOptic Card-MT (multi-mode)

• FiberOptic Card-VF (multi-mode)

Features/Specifications

• Standards: IEEE 802.3u Fast Ethernet 100Base-FX

• Bus Type: 32-bit PCI

• Fiber Optic Connector:

ST/SC/MT-RJ/VF connector (multi-mode), Tx/Rx

• Fiber Optic Cable:

50/125, 62.5/125 or 100/140 µm (multi-mode)

• Data Transfer Rate/Mode: Up to 100Mbps, half- or full-duplex

• LED Indicators:

LED Color Function

ACT Green Blinks when any traffic is present

LINK Green Lit when fiber cable connection is good

FDX Green Lit when full-duplex mode is active

COL Green Blinks when collision signal is present

• NOS Supported: Windows 95/98, Windows NT, Windows

2000, Windows for Workgroups, NetWare, IntraNetWare,

Microsoft LAN Manager, OS/2 Warp, IBM LAN Server,

SCO UNIX

04-0176A

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Quick Installation Guide

1FiberOptic CardQuick Installation GuideThis quick installation guide provides instructions for installing a 100Base-FXPCI FiberOptic Card.1-1 Intro

Strany 2 - 2-1 Hardware Installation

2• Power Requirement: 0.2A @ +5V• Operating Temperature: 32° to 122° (0° to 50°C)• Storage Temperature: -40° to 158°F (-40° to 70°C)• Relative Humid

Strany 3 - Connecting

3Caution: Static Electricity Discharge may permanentlydamage your system. To avoid possible static electricitydischarge during the installation, plea

Strany 4 - 3-1 Software Installation

43-1 Software InstallationThis section will guide you through the installation of the MicrosoftWindows software drivers.Please refer to the appropriat

Strany 5 - Windows 98/98SE

5Windows 98/98SEPerform the steps below to install the Windows 98 driver files,which are built into Windows98/98SE.1. When Windows 98/98SE boots up af

Strany 6 - Windows 2000

6Windows NT 4.0Perform the steps listed below to install the following Windows NT 4.0driver files:Location of Driver: A:\WINNT\DC21X4.SYS \OEMSE

Strany 7 - Step 3: Ship the product

74-1 Technical Support & RMAQuestions? SIIG’s On-line Support has the answers! Simply visitour web site at www.siig.com and click on the ON-LIN

Strany 8

Komentáře k této Příručce

Žádné komentáře

SIIG RS-232 to Multi-Mode Fiber Optic Instalační příručka

Procházejte online nebo si stáhněte Instalační příručka pro Síťové karty SIIG RS-232 to Multi-Mode Fiber Optic. SIIG RS-232 to Multi-Mode Fiber Optic Installation guide Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce