SIIG Serial ATA 4-Channel PCI Uživatelský manuál stáhnout pdf

Serial ATA 4-Channel PCI

Quick Installation Guide

04-0322C

Introducing the Serial ATA 4-Channel PCI

The Serial ATA 4-Channel PCI is an ultra high-speed four

channel Serial ATA controller for use in Pentium-class

computers. It achieves burst data transfer rates up to

150MB/s (1.5Gb/s) and supports various brands of hard

disk drives with capacities greater that 137GB.

Features and Benefits

• Compliant with Serial ATA Specification, rev 1.0

• Compliant with PCI Specification, revision 2.2

• Provides four independent channels to support up

to four Serial ATA drives

• Features independent 256-byte FIFOs per channel

for host reads and writes

• Co-exists with on-board HDD controllers

• Features Watch Dog timer for fault resiliency

• Supports 32-bit wide PCI bus at 66MHz

• Lower pin count and voltage requirements, plus

better cabling over traditional Parallel ATA (IDE)

make Serial ATA the controller of the future

System Requirements

• Pentium

class computer with one available PCI

slot

• Windows

98SE / ME / NT4.0 / 2000 / XP (32-/64-

bit) / Server 2003 & 2008 (32-/64-bit) / Vista (32-/

64-bit)

• CD-ROM

1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - Serial ATA 4-Channel PCI

1Serial ATA 4-Channel PCIQuick Installation Guide04-0322CIntroducing the Serial ATA 4-Channel PCIThe Serial ATA 4-Channel PCI is an ultra high-speed f

Strany 2 - Hardware Installation

105. Select Silicon Image SiI... SATALink Controller,then click Next.6. Follow the on-screen instructions to complete theinstallation.For Existing Ins

Strany 3 - Device Connection

118. Click Yes, then click Finish to complete.For Existing Installation1. Install the board and boot up Windows.2. At the Add New Hardware Wizard, cli

Strany 4 - Driver Installation

12For Existing Installation1. Install the board and boot up Windows.2. At the Add New Hardware Wizard, insert the driverCD.3. Select Specify the locat

Strany 5

135. Select Silicon Image... Controller for Windows NT4.0 and 2000, and press Enter.6. Press Enter to continue and follow on-screeninstructions to c

Strany 6

14Bios ConfigurationThe Serial ATA 4-Channel PCI BIOS will appear everytimeyour system starts up. If the bios doesn't show, please tryyour contr

Strany 7 - Windows Vista™ (32-bit)

15Technical Support and WarrantyQUESTIONS? SIIG’s Online Support has answers! Simply visit ourweb site at www.siig.com and click Support. Our onlin

Strany 8 - Windows Vista (64-bit)

Serial ATA 4-Channel PCI is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarksof SIIG, Inc. Microsoft, Windows and Windows V

Strany 9 - Windows Server 2008 (64-bit)

2Package Contents• Serial ATA 4-Channel PCI board• Serial ATA cable (x2)• Dual connector Serial ATA power cable• Driver CD• This quick installation gu

Strany 10 - Windows 98SE

31. Turn OFF the power to your computer.2. Unplug the power cord and remove your computercover.3. Remove the slot bracket from an available PCI slot.4

Strany 11 - Windows ME

4Note: If you like to monitor disk activity of theSerial ATA hard drives, you may at this time connectthe hard disk LED of the system case to the Har

Strany 12 - Windows NT4.0

5For Existing Installation1. Install the board and boot up Windows 2000.2. At the Found New Hardware Wizard, click Next.3. Select Search for a suitabl

Strany 13

62. At the Found New Hardware Wizard:XP (w/SP1 or earlier)/Server 2003: continue to step #3.XP (w/SP2 or later)/Server 2003 (w/ SP1 or later): selectN

Strany 14 - Bios Configuration

73. Insert the driver CD, select Install the softwareautomatically (Recommended), and click Next.4. Click Finish and restart Windows to complete thein

Strany 15

8Windows Vista (64-bit)For New Installation1. Install the board and follow Microsoft proceduresto install Windows accordingly.2. At Where do yo want t

Strany 16 - About SIIG, Inc

9Windows Server 2008 (32-bit)For New Installation1. Install the board and follow Microsoft proceduresto install Windows Vista accordingly.2. At the Wh