SIIG USB Over IP Uživatelský manuál

USB Over IP User’s ManualSIIG’s ONLINE SUPPORT andProduct RegistrationVisit SIIG’s web site at www.siig.com and clickSuppo

Introduction1-5Ethernet PortPower Adapter JackUSB PortsReset ButtonFigure 2: Back Layout• Reset Button: Use this button to restore the defaultsetting

USB IP Admin Software Utility2-1Chapter 2Hardware Installation andDevice Compatibility2-1 Hardware InstallationGeneral hardware installation instruct

User's Manual2-22-3 USB Device SupportUSB Over IP Admin client software is based on openarchitecture, wherein the USB over IP box virtualizes t

USB IP Admin Software Utility2-32-3.1 Device Interoperability List Cont'd.Device Type Make ModelWebcamLogitech Quickcam MessengerLogitech Quickca

User's Manual2-42-3.1 Device Interoperability List Cont'd.Device Type Make ModelKeyboardAcer Acer KeyboardApple Mac Mac Extended KeyboardMic

USB IP Admin Software Utility2-52-3.1 Device Interoperability List Cont'd.Device Type Make ModelPrintersHPBusiness InkJet 1200DeskJet D2360LaserJ

Driver Installation3-1Chapter 3Driver Installation3-1 Driver InstallationThis section provides information on how to install theUSB over IP drivers.

User's Manual3-25. At Choose Components, click Next.6. At Choose Install Location, click Install.

Driver Installation3-37. At the Security Alert, click Yes. (skip this step for32-bit XP)8. Click Yes to add the application to WindowsFirewall except

User's Manual3-49. At the Found New Hardware Wizard, select No,not this time, click Next. (skip this step if notprompted)10. Select Install the

USB Over IP is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG,Inc. Microsoft and Windows are registered trademar

Driver Installation3-511. At the Security Alert, click Yes. (skip this step for32-bit XP)12. Click Finish.

User's Manual3-613. At Windows Security Alert, click Unblock. (skipthis step if you clicked Yes to add this applicationto firewall exceptions lis

Driver Installation3-74. At the USB Over IP screen, click Install.5. At Choose Components, click Next.

User's Manual3-86. At Choose Install Location, click Install.7. At Security Alert, click Yes.

Driver Installation3-98. Click Yes to add the application to WindowsFirewall exceptions list, then click Finish.9. At the Found New Hardware Wizard,

User's Manual3-1010. Select Install the software automatically(Recommended), click Next.11. At Security Alert, click Yes.

Driver Installation3-1112. Click Finish.13. Repeat steps 9-12 for each USB Over IP connectedthat matches your subnet address.3-1.3 Windows Server 20

User's Manual3-124. At the USB Over IP screen, click Install.5. At Choose Components, click Next.

Driver Installation3-136. At Choose Install Location, click Install.7. At Windows Security, click Install this driversoftware anyway two times.

User's Manual3-148. Click Yes to add the application to WindowsFirewall exceptions list, then click Finish. ClickFinish.3-1.4 Windows Vista (

User's ManualiiContentsChapter 1: Introduction1-1 Unpacking the USB over IP ... 1-11-1.1 Stati

Driver Installation3-15If Auto Play doesn't start: click Start, in the StartSearch box, type D:\Launch.exe. (Change D: tomatch your CD-ROM drive

User's Manual3-165. At Choose Components, click Next.6. At Choose Install Location, click Install.

Driver Installation3-177. At Windows Security, click Install this driversoftware anyway two times.8. Click Yes to add the application to WindowsFirew

User's Manual3-183-1.5 Windows 7 (32-bit)1. Connect the USB over IP to your network.2. At the Windows desktop insert the driver CD.At the Auto

Driver Installation3-194. At the USB Over IP screen, click Install.5. At Choose Components, click Next.

User's Manual3-206. At Choose Install Location, click Install.7. At Windows Security, click Install this driversoftware anyway two times.

Driver Installation3-218. Click Yes to add the application to WindowsFirewall exceptions list, then click Finish tocomplete the installation.9. Right

User's Manual3-2210. Click Compatibility tab. Check Run this programas an administrator, click OK (after clicking OK,wait up to 30 seconds to co

Driver Installation3-2312. Right click the USB Over IP Admin icon, clickProperties.13. Click Compatibility tab, check Run this programas an administra

User's Manual3-2414. Double click the USB Over IP Admin icon on thedesktop. If prompted click Yes at the User AccountControl box to continue.3-2

ContentsiiiChapter 4: USB Over IP Admin4-1 Introducing the USB Over IP Admin ... 4-14-2 Using the USB Over IP Admin

Driver Installation3-253-3 Set IP Address3-3.1 Change Subnet AddressThe factory default IP address given to the USB Over IPis 192.168.3.22. This

User's Manual3-263. At the Welcome to USB Server Setup screen, if yourUSB Over IP doesn't show up, go directly to section3-3.2 IP Config - D

Driver Installation3-275. Click Yes to save your settings, then click OK.3-3.2 IP Config - DiscoveryUtility1. Insert the USB Over IP CD.2. Click the

User's Manual3-283. At List of Servers, double click the MAC address ofthe USB Over IP you want to change.4. At IP Configuration screen, either t

Driver Installation3-295. At the List of Servers box click Refresh to viewyour changes. When ready, click Exit to close theutility.

Configuration Utility4-1Chapter 4USB Over IP Admin4-1 Introducing the USB Over IP AdminThe USB Over IP Admin is a user friendly PC softwarewhich sup

User's Manual4-24-2 Using the USB Over IP AdminThe USB over IP Admin is used to connect to your USBdevices and configure your USB Over IP serv

Configuration Utility4-34-2.2.1 USB Device Function Buttons• Refresh: refreshes USB device list• Connect: connects to a free USB device• Disconnect:

User's Manual4-44-2.3.1 Server Function Buttons• Refresh: searches for servers• Unlock: unlocks password enabled servers• Upgrade: upgrades ser

Configuration Utility4-54-2.4.2 Help• Help: opens online help document• About USB Over IP Admin: view systeminformation including version number and

User's ManualivAbout This ManualThe purpose of this manual is to introduce you to yourUSB over IP server. It will guide you to properly configur

User's Manual4-64-3 How To's4-3.1 Device Mapping4-3.1.1 How to Connect - Status Free1. In the Device Mapping window, select a devicewh

Configuration Utility4-74-3.1.2 How to Connect - Status BusyInstead of waiting for a device to become Free, you maysend a request to release the dev

User's Manual4-84-3.1.3 How to Disconnect1. In the Device Mapping window, select a devicewho's status is Connected, then click the Disconn

Configuration Utility4-94-3.1.4 USB Device - Disable Auto ConnectAuto Connect is enable, by default, whenever the USBOver IP is started. However, i

User's Manual4-104-3.1.5 Printer SharingThe Printer Sharing feature automatically connects anddisconnects your printer from your computer every

Configuration Utility4-114-3.2 Server Manager4-3.2.1 Setup (Server Configuration)Use the Setup button to change server name, modify IPsettings and

User's Manual4-124. Select IP Settings tab. Check Modify, then eitherselect Static and type in your IP address andgateway or, to have your serv

Configuration Utility4-134-3.2.2 Unlock Server and Reset the PasswordWhenever the USB Over IP is password protected,Locked will display in the Status

User's Manual4-143. Your password will be confirmed or denied, clickOK. If failed, try again. If you continue to haveproblems, check with your

Configuration Utility4-155. Select the Password tab.6. Check Modify, uncheck Enable Password, thenclick Save.

Introduction1-1Thank you for your purchase of the USB over IP. SIIG’sgoal is to provide reliable, high quality products and fastcustomer support.The p

User's Manual4-164-3.2.3 Refresh (Refresh Servers)1. Click the Refresh button.2. The Searching for Servers box will pop up.

Configuration Utility4-173. The Server Manager list will be refreshed.4-3.2.4 Restore (Restore Factory Default Settings)The factory default settings

User's Manual4-182. Click OK.3. Click OK again.4. Click Refresh to display the server list.

Configuration Utility4-194-3.2.5 Upgrade (Upgrade Firmware)1. Select a server, click the Upgrade button.2. In Select File box, browse to or type in t

User's Manual4-204-3.2.6 Configure IP Address: Server Not On the SameSubnet1. At the Server Manger screen, select the server thatis not on the

Configuration Utility4-213. In Server Settings, either select Static and type inthe IP address and Gateway or select DHCP tohave them assigned by the

User's Manual4-225. At the Server Manager screen, click Refresh. Yesshould be displayed in the Same Subnet? column ofthe server.4-3.2.7 Configu

Configuration Utility4-233. At List of Servers, double click the MAC address ofthe USB Over IP you want to change.4. At IP Configuration screen, eithe

User's Manual4-245. At the List of Servers box, click Refresh to viewyour changes. When ready, click Exit to close theutility.

5-1Technical Support & Product Return5-1 OverviewThis chapter will give you instructions on how to obtainproduct information, contact technical

1-2User's Manual1-1.1 Static Electricity PrecautionOne of the routine precautions you must be aware ofwhen working with computer components is

5-2User's Manual5-2 Technical Support and WarrantyQUESTIONS? SIIG’s Online Support has answers! Simply visit our website at www.siig.com and

5-3Technical Support & Product ReturnBlank Page

03-0315B

Introduction1-31-2 Introducing the USB over IPThe USB over IP allows network users to connect remoteUSB devices like, printers, scanners, digital cam

1-4User's Manual1-2.2 System Requirements• Windows® 7 (32-bit) / Vista (32-bit) / XP (32-/64-bit) / Server 2003 (32-/64-bit) / Server 2008 (32